Power Supply Monitor Using LM3914_programmable timer Supply Voltage

You may find:

Intermatic Instruction Manuals ; 7 day programmable timer ; programmable water timers ; multiple on/off daily programmable timer ; programmable timer VDC ; Programmable Appliance Timers

Power Supply Monitor Using LM3914

Tag：programmable timer Supply Voltage programmable timer |

65 Viewers|

freeelectricalsandtools 2009-05-19 21:26:14 Publish:

This circuit is use to a few resistors and some LED, a simple expanded-scale voltmeter is easily constructed. Furthermore, it runs from the same single 5V ± 10% supply it monitors and can provide TTL compatible under voltage and over voltage warning signals. The complete circuit is shown in this figure.

This circuit is useful where quick and easy voltage adjustments must be made, such as in the field or on the production line. The circuit’s low cost makes it feasible to incorporate it into the system, where the overvoltage and under voltage warning signals provide an attractive extra. Of course, these techniques can be used to monitor any higher voltages, positive or negative. Calibration procedure is the LM3914 output thresholds have been shifted up by 100 mV and output #10 is or-tied with output #9. Other outputs may be wire or together if 100 mV resolution is not necessary. If desired, the outputs can be color coded by making LED #1 and LED #10 red, LED #2 and LED #9 amber, and the rest of the LEDs green to ease interpretation.

To calibrate, set VCC at 5.41V and adjust R6 until LED #9 and LED #10 are equally illuminated. (A built-in overlap of about 1 mV ensures all LEDs won’t go out at a threshold point.) There’s no need to vary the system supply voltage to perform this adjustment. Instead, disconnect R1 from VCC and connect it to an accurate reference. Then, at 4.5V, adjust R4 until LED #1 just barely turns on. There is a slight interaction caused by the finite resistance (10k, type) of the LM3914’s voltage divider, so that repeating the above procedure once is advised. The LED driver outputs can directly drive a TTL gate, so that the LED #1 and LED #10 outputs may be used for under voltage and overvoltage warning signals. These may be used to initiate a soft shutdown or summon an operator, for example. The 470Ω resistor R8 ensures that the LM3914 output will saturate to provide the proper TTL low level. Pull-up resistor R9 provides the logic high level.

Yahoo: programmable timer Power Supply Monitor Using LM3914 programmable timer Supply Voltage
Google: programmable timer Supply Voltage Power Supply Monitor Using LM3914 programmable timer

6
DIG IT

Related

›› Sub-Woofer Graphic Equalizer with 8 Band
›› Phototransistor for High Impedance Voltm
›› TTL Power Supply with Crowbar protection
›› Watt Meter Digital 1 Phase 1 With Microc

Timer Latest

›› Provident Living: Ways to Lower your mo
›› ATC Timers and Counters
›› Delonghi DCM485 10 Cup Stainless Steel C
›› Best Price Cheap KitchenAid appliances
›› Sub-Woofer Graphic Equalizer with 8 Band
›› Phototransistor for High Impedance Voltm
›› Power Supply Monitor Using LM3914
›› Nike heart rate monitors
›› openSuse 11.1 on Virtual PC 2K7: norepla
›› MCS-85 Family:
›› Programmable Interval Timer(8253)
›› how to choose the best coffee maker for

Timer Popular

›› Nike heart rate monitors
›› Programmable Interval Timer(8253)
›› SKRIPSI TEKNIK MESIN [KODE 12GM]
›› Power Supply Monitor Using LM3914
›› MCS-85 Family:
›› Does anyone have instructions for a Smit
›› Best Price Cheap KitchenAid appliances
›› Phototransistor for High Impedance Voltm
›› Sub-Woofer Graphic Equalizer with 8 Band
›› openSuse 11.1 on Virtual PC 2K7: norepla
›› Wedding Countdown and Heart Frame Freebi
›› Provident Living: Ways to Lower your mo